Ghost 2 Immobiliser Reviews
The ghost 2 immobiliser is a cutting-edge anti-theft system that uses advanced technology to prevent car theft. This hidden device is not detected by thieves and only starts your engine after an app or PIN code is entered.
It connects to the CAN data network in your vehicle and is weatherproof. It also comes with a service/valet mode, which allows you to temporarily start your car while it's in garage for servicing or cleaning.
Easy to install
The Ghost immobiliser is a cutting-edge security tool that shields your vehicle from cloning, hacking, and key theft. It is a unique PIN code system integrated with the car's ECU, making it difficult for thieves to detect or tamper with. It's not visible and does not use any sensors or special keys. It is also cheaper than replacing an ECU or installing a new key fob and could lower the cost of your monthly insurance.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's directions carefully. This will ensure that the device works correctly and effectively. Test the system after installation by entering the PIN and then starting the vehicle. Regular testing will enable you to detect any issues in the early stages.
Before beginning the installation, double-check the location of the CAN H and L wires. They are vital to power the immobiliser, so it is essential that they are connected properly. It is also recommended to label the wires to make it easier to identify them during the installation process. Once you have identified the location of these wires and connected them to a continuous 12V power source as well as the grounding point. Use a fuse tap to shield the connections from short-circuits or damage.
After connecting the wires, neaten the wiring with cable ties to avoid potential alteration. You can also cover the connections with insulation tape or heat-shrink tubing. This will help protect them from electrical shorts, and will increase the life span of the device. It's a great idea to test your Ghost 2 immobiliser once the wiring is secured.
In situations where you have to hand over your vehicle, such as for valet parking or servicing or valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. Press the brake pedal, and hold the accelerator down for a number of times equal to the first digit of the emergency code. The system will then go into service mode, which is confirmed by flashing the indication signal five times.
It is simple to change PIN codes
A ghost 2 immobiliser is a great way to protect your vehicle from theft. It is hidden within the vehicle and can only be accessed by a unique code. The device communicates with the vehicle ECU through its data bus. It does not rely on radio frequency signals like aftermarket alarm systems or traditional Thatcham immobilisers do. This makes it difficult for thieves to detect the sound of an immobiliser relay, or to add new key fobs. The control unit is hidden in the wiring harness or dashboard, and cannot be physically altered to reset the system.
The ghost 2 immobiliser is linked to the vehicle's CAN Data network. It makes use of buttons on the steering, door panels and the center console, to create a customisable series of up to twenty button presses, which must be entered to start the engine - just as a PIN. This unique system can be reprogrammed and does not require wire cutting during installation. You can even set your vehicle in Valet or Service mode to allow it to be started for a short time when you give it to a mechanic to work.
The app can also be used to disable your PIN number if you've lost your keys, or change it. This feature is particularly useful in the event that you have offered your vehicle to someone else to use as a valet parking space or for servicing since it prevents them from starting your car and taking it away without consent. It is also undetectable by professional thieves since it doesn't make use of circuit cuts or radio frequencies.
The ability of the immobiliser to prevent relay thefts is another important feature. Relay theft is a popular method of car theft, where the criminals hack into the diagnostic port on your car and then alter the signal sent by the key to the vehicle's ECU in order to fool it into believing that the key is valid. The traditional immobiliser can be manipulated in this way, but with the ghost 2 immobiliser the signal is blocked by the immobiliser before it gets to the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that safeguards your car from hacking, key-cloning and key theft. It works by connecting to the CAN data network in your vehicle and requiring you to enter a PIN number before it can start the engine. It also deters thieves from using signal spoofing or device spoofing, which are common tactics employed to steal vehicles.
The system is easy to use and works just like a standard car alarm. Once you have installed it, you can create an individual PIN code sequence of up to 20 characters long, which will have to be entered before the vehicle is started. This will stop the vehicle from being stolen even if your keys are stolen. You can turn off the system with an app on your smartphone.
The ghost is silent and does emit radio frequency signals. It is a discreet weatherproof device that can be placed anywhere in your vehicle. It can be concealed under the dash, steering wheel, or on the door panels. It communicates with your ECU via the CAN data circuit and is not affected by diagnostic tools that some thieves use to identify security systems. It is also not affected by jamming devices that alter codes.
It is a security system that can be used to prevent the theft of all vehicles. Its technology has been proven to be effective, and it complies with TASSA Standards. The Ghost is a great option for classic, sports, and prestige automobiles. It can be used as a way to protect vehicles being rental on apps such as Turo.
The Autowatch Ghost 2 represents the next generation of car immobilisers. This system is invisible to thieves, and prevents the vehicle from starting without your PIN or unless they have been authorized by the app. It doesn't emit radio frequencies or any other signals that scanners detect. Installation is simple and quick. ghost 2 immobiliser cost is easy to navigate and offers a user-friendly interface which makes it simple to install and use. It also comes with a GPS tracker that can help police locate and locate the vehicle.
Easy to reset
It is possible to protect your vehicle from theft using a ghost 2 immobiliser. It is integrated into your vehicle's ECU and creates a security barrier that thieves are unable to breach without the correct pin. It's also TASSA verified which means it's recognized by insurance companies. It's a useful tool to prevent car theft and will save you money in the end.
Contrary to traditional alarms/immobilisers which require cutting of circuits and circuit cutting, the Ghost system is connected directly to the vehicle's CAN data network and works using your existing buttons on the dashboard as well as the steering wheel. You can create an individual PIN sequence that can be up to 20 presses long. This PIN needs to be entered before the engine can begin, just like the PIN you use on your credit card. Ghost is inaccessible to thieves and has no indicators that give away its presence, which makes it the most effective aftermarket CAN bus immobiliser on the market currently.
Another advantage of the Ghost system is that it doesn't utilize radio frequency signals, which means it cannot be detected or scanned by thieves. This is a deterrent to key attacks that replicate and relay attacks, as and the typical method of hacking into a car's computer system using its CAN bus by scanning for signals. In addition to that, the Ghost system is designed to be completely hidden in your vehicle and there aren't any lights or signals to indicate its presence.
The system has an option called Transport Mode which disables the Ghost System. This is useful in situations where you require a temporary deactivation of Ghost for instance, when you are transporting or maintaining your vehicle. This mode is less effective than Service Mode as it doesn't disable the Ghost system if you exceed 31 mph in 15 minutes.
To reset your ghost 2 immobiliser you will need to have the emergency code, which is available from your installer. The code is typically hidden under the scratch-off area of the card you received with the installation. This emergency code should be secured and kept in a safe place like your wallet at home.